Pellet stove

I. STOVE USER MANUAL

CLOE3 version
CLOE3_FR
CLOE3_EN
CLOE3_DE

GRACE3 version
GRACE3_FR
GRACE3_EN
GRACE3_DE

II. USE AND PROGRAMMING OF THE GRACE 3 STOVE

Stove installed between January 2020 and December 2022

II. 1. Programming temperature

Use the pellet stove during the cold season to keep plants frost-free. The goal is not, however, to have the same temperature in the greenhouse as in summer.

Adjust the temperature

Press the + - buttons.
Scroll with the arrows to T° amb. Press Menu then + - until the desired temperature. Press Menu to confirm the setting.
To return to the initial page, press off.

Flame power

Press the + - buttons.
Scroll with the arrows to Flamme. Press Menu then + - until the desired flame power. Press Menu to confirm the setting.
To return to the initial page, press off.
For good combustion, set the flame power to 4.

Enable/disable Auto-Eco mode

Press the Menu button.
Move with the right arrow until "Sélection".
Confirm by clicking the Menu button.
Move again with the arrow until "Auto-Eco".
Disable by clicking -. The Auto-Eco mode is then "Off".

To return to the initial page, press off.

When the stove reaches the set temperature, the appliance switches off automatically. It switches back on when the temperature drops again to 2° below the setpoint. In the 'Sélection' menu, make sure that the "Auto-Eco" mode (or "Stand By" for the old stove model) is ON to benefit from AUTO start/stop mode.

4011 — "Auto-Eco" or "Stand By" mode (old model).

Add programs

Press Menu.
Move to Timer using the arrow.
Press Menu.
The first program (P1) is selected.
Press + - to select "ON".
Confirm with the Menu button.
Change the time by pressing + and - , press Menu to confirm.
Select the operating days with + - and confirm with the Menu button.

Recommended programming

The programming has been tested for temperatures down to -10°C. It provides pellet autonomy of about 3 to 4 days.

This programming provides heat early in the day. Then, the increase in outdoor temperatures during the day and the presence of sun will take over. The rapid temperature increase helps reduce humidity in the greenhouse and therefore fungal diseases. Condensation also decreases more quickly and the greenhouse effect will be strengthened earlier in the day.

For this programming, disable Auto Eco mode to avoid overconsumption of pellets.

Program	Days	Times	Temperatures
Program 1	Monday to Sunday	7h30 - 9h30	30°C
Program 2	Monday to Sunday	16h-18h	30°C
Program 3	Monday to Sunday	1h-3h	30°C

II. 2. Pellet supply

Your stove will trigger an alarm when its pellet hopper is empty. Simply fill the stove and press and hold the start button to clear the error message and restart the appliance. Expect 2 to 3 bags of pellets per week depending on your geographical location.

When the pellet feed auger is empty, it is recommended to manually place a handful of pellets in the burner at the first start-up, while the auger fills up again.

II. 3. Maintaining the combustion chamber

It is recommended to clean the stove once every two weeks.

Empty the ashes by removing the ash drawer or vacuuming them with an ash vacuum.

❗️
Warning
Do not use a household vacuum cleaner to vacuum ashes. If an ember is still lit, it could catch fire.

Remove the burner and vacuum the debris until the air holes are completely clear
Put the burner back in place
Clean the glass with a damp cloth
Restart the stove

Once a year, it is recommended to call in a professional to service your stove and sweep the chimney flue.

II. 4. Summer maintenance of the stove

At the end of winter, make sure not to leave pellets in the stove hopper to prevent them from absorbing moisture and clogging the ducts.

You can also leave the stove door slightly ajar to prevent moisture from settling inside.

👍
Tip
Ash is very good for your vegetable garden! Feel free to use it in your crops.

II. 5. Chimney management

The smoke evacuation duct coming from the stove is very important. It is therefore necessary to check that it is clean and working properly.

If soot builds up for a long time, it eventually clogs the duct starting from the elbow coming out of the stove. This results in very heavy smoke, yellowish in colour and with a pungent smell.

In this case, dismantle the chimney and thoroughly clean the inside using a special brush and water. It is useful to let the chimney parts drain well to prevent moisture from getting back into the stove.

699 — Heavy smoke coming from the blocked chimney

II. 6. Cleaning the smoke chamber

Every 4 to 8 weeks

Behind the rear plate of the stove, remove the nuts
Vacuum the ashes
Put the plate and nuts back

II. 7. Cleaning the smoke duct

Every month

Remove the cap from the smoke duct
Empty the contents of the cap
Vacuum the ashes inside the T-piece
Put it back in the system

1106 — Accumulation of ash and condensation in the collection cap

📘
The following operations must be carried out once a year by a technician

Cleaning the smoke extractor

Cleaning the room fan

Sweeping the soot accumulated in the smoke duct and chimney

Replacing damaged seals

III. USER MANUAL AND PROGRAMMING OF THE NATALIA STOVE

Stove installed since January 2023

Characteristics:
Tank capacity: 13 kg
Thermal power: maximum 8 kWh
Reduced power: 2,4 kWh
Fuel: good quality wood pellets.

Manufacturer manual: MYFOOD-NOTICE-POELE-NATALIA.pdf

Loading pellets
Put the wood pellets into the hopper slowly.
Do not put any around the door, otherwise it may jam.
If the door remains open for more than 45 s while the stove is operating, it goes into error mode.
After filling the hopper, make sure the door is properly engaged so that the hopper is hermetically sealed, otherwise the stove will not start operating.

Pellets must be stored in a dry place (and not in the greenhouse) to prevent them from absorbing moisture. If the pellet is damp, the stove may not start properly and may generate an error.

Before the 1st ignition, the operation can be repeated 3 times to successfully light the stove.

III. 1. Select the language

Press On/Off
Press Set
Press the temperature +/- to choose the parameter to configure, until "SELECT LANGUAGE"
Press SET to enter the program
Press the flame +/- to choose the language (Deutsch, English, Français)
Press SET to confirm
Press On/Off to return to the main page.

III. 2. Set the date and time

Press On/Off
Press Set
Press the temperature +/- to choose the parameter to configure, until "REGLAGE DATE ET HEURE"
Press SET to enter the program
Press the flame +/- to choose day, month, year and time.
Press SET to confirm
Press On/Off to return to the main page.

III. 3. Add a weekly program

Press On/Off
Press Set
Press the temperature +/- to choose the parameter to configure, until PROG. HEBDO
Press SET to enter the program

Press the temperature +/- to choose LV or SD days, or according to the days required:

LV : Monday to Friday
SD : Saturday and Sunday
For operation throughout the week, you will need to create 2 programs: one from Monday to Friday and a second for the weekend.

Press the flame +/- to navigate to:

The start time,
The stove operating temperature,
Its power – P5 provides good combustion,
Choose On to start the program and Off
Select Habil (enabled so that it is taken into account)

Press SET to confirm and move to the next program.
Programming example:

F01 : LV, 7:00, 20°C, P5, On, Habil
F02 : LV, 9:00, 20°C, P5, Off, Habil
F03 : SD, 7:00, 20°C, P5, On, Habil
F04 : SD, 9:00, 20°C, P5, Off, Habil
F05 : LV, 16:00, 20°C, P5, On, Habil
F06 : LV, 18:00, 20°C, P5, Off, Habil
F07 : SD, 16:00, 20°C, P5, On, Habil
F08 : SD, 18:00, 20°C, P5, Off, Habil
F09 : LV, 1:00, 20°C, P5, On, Habil
F10 : LV, 3:00, 20°C, P5, Off, Habil
F11 : SD, 1:00, 20°C, P5, On, Habil
F12 : SD, 3:00, 20°C, P5, Off, Habil

To save pellets, at the start of the winter season, only one time slot can be activated (F01 to F04).

The idea is to keep the greenhouse frost-free rather than maintaining a high temperature at all times.

III. 4. Manual or automatic mode

By pressing AUTO, you choose whether the stove operates in automatic or manual mode.
When the stove operates in automatic mode, it follows the saved programming. In Manual mode, the stove only starts operating when you start it manually.

III. 5. Maintenance

With the weekly programming indicated, the combustion chamber and the burner must be cleaned every 2-3 days with an ash vacuum and when the stove has cooled down.